CANopen - CAN Bus 之工業控制|eAutomind

wwwMicroport

 現在的位置: 首頁產品簡介

Fiber Optic Bridge Generation II with CAN Bus

(未稅)台幣定價:0
產品價格標示為"0"表示未定價,
    索取報價請按聯絡我們
Fiber Optic Bridge Generation II with CAN Bus
 

簡易規格下載

Fiber Optic Bridge Generation II with CAN Bus

Fiber Optic CAN Bus Bridge II

Part No: MPDG-Generation-II-Fiber-Optic-CAN-Bridge

Fiber optic converters that electrically isolate signals from the vehicle bus using common bridge and satellite modules interconnected with fiber optic cable for EMI and EMC testing.

Differentiation

Interchangeable bridge modules with built-in functionality for:

  • High and Low Speed CAN (HS CAN, LS CAN)
  • Single Wire CAN (SW CAN)
  • CAN FD

Key Features and Protocols

High Speed CAN with CAN FD Support

  • High speed CAN to 1 M bps
  • ISO 11898 physical layer
  • Terminating resistor options via rotary switch
  • None
  • 120 Ohm
  • Split 120 ohm
  • ISO15765 AC termination

Hardware Specifications

  • Physical Demensions: 6.5" x 4.125" x 1.5"
  • Weight: 12.6 oz
  • Operating Range: -10°C to 80°C
  • Electrical: 8-18 VDC

Ease of Use

The new Gen II CAN Fiber Optic Bridge offers a simplistic approach for EMI/EMC testing using fiber optic signal communication.

All necessary components for connecting data monitoring equipment to a vehicle bus are included in the kit.

Connection Process

Fiber Optic CAN Chamber

  • Place the local and remote bridge modules into position
    (EMC chamber/monitoring equipment)
  • Connect the bridges together using the fiber optic cable provided
  • Set the bridge modules for proper termination and protocol
  • Connect the vehicle bus to the remote module using the high density 15 pin D connector.
  • Connect the monitoring equipment to the bridge module using the high density 15 pin D connector.
  • Begin EMI testing initiatives.

Benefits

  • Transmits signals between a Device Under Test (DUT) and monitoring equipment
  • Provides optical isolation of vehicle networks during EMI/EMC testing
  • Compatible with all CAN protocols
  • Quick and easy set up with user friendly controls
  • Only requires two fibers between bridge and satellite module
  • Exceeds or meets automotive EMC testing specifications
    • Radiated emissions
    • Bulk current Injection
    • Radiated susceptibility
  • Rechargeable batteries provide minimum 12 hours of operating time before requiring recharge

CAN FD Support

  • Supports the new high speed CAN standard from Bosch
  • High speed CAN arbitration phase to 1 M bps
  • Data Phase to 5 M bps

Single Wire CAN Support

  • Normal and High speed modes
  • With or without tool termination resistor
  • Fully compliant to GMW3089 V2.4 and J2411 Single Wire CAN specification for Class B in-vehicle communications
  • Accurate pass-thru of High Voltage Wakeup signals at Normal bus speeds

Meets Radiated Susceptibility Specifications

The radiated susceptibility of our hardware is to 600 V/meter, reverb and 100 dB (uA), B.C.I.

Requirement levels for the immunity to electromagnetic fields for component and subsystems measured in the anechoic chamber DUT functiona may only deviate above the levels according to the table:

Fiber Optic Bridge II - Radiation Specifications

Meets Radiated Emmission Specifications

Fiber Optic Bridge II - Emission Specifications

Meets Bulk Current Injection Specifications

Requirement levels for the immunity to electromagnetic fields for components and subsystems measured using the CBCI and DBCI method.

Fiber Optic Bridge II - Injection Specifications

 

 

 

 

 

 

 

Fiber Optic Bridge Generation II with CAN Bus簡易規格下載
 

最新消息| 公司簡介| 產品簡介 | 線上報價 | 經銷夥伴 | 下載 | 搜尋商品 | 聯絡我們

© 2018 標高電子股份有限公司 著作權所有,並保留一切權利。